Lightforce HANDHELD SEARCHLIGHTS SL Variable Instrukcja Użytkownika Pobierz pdf (Strona 1)

1. DO NOT leave light connected to a power source when not in use.

2. DO NOT place light face down on ANY surface. If the light is switched on the intense heat generated may ignite the surface

and cause a meltdown of the lamp body.

3. Ensure all electrical connectors are secure - loose connections will generate excessive heat, damage wiring and cause

electrical failure.

4. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry rag will

 scratchthelens,especiallyifthesurfaceisdusty.NEVERcleanthelightwithcleaninguidorsolvent.

5.DONOTattempttocleantheinsideofthelightortouchtheinsidelensandreector.

6.LIGHTFORCElightsarenotdesignedtobeusedforlongperiodsoftimeinastationarypositionwithminimalairow,failureto

comply will void warranty. Contact LIGHTFORCE direct to discuss alternative options such as reducing globe wattage.

7.GLOBEREPLACEMENT:TheXenophot®globegivesapproximately10%greaterefciencythananyotherhalogenglobeof

similar wattage. A number of optional globe strengths are available upon request. For removal, simply:

  a)Rotatethereectorhousinganti-clockwisetodisengageit.

  b)Removeoldglobebygrippingrmlyandpullingoutinthelongaxisdirectionoftheglobe.

i) DO NOT TOUCH NEW GLOBE WITH FINGERS, use a tissue or plastic sleeve. Prior to inserting a new globe, scrape the

 globelegswithanabrasivesurface(sandpaperorknifeedge)toensurepositivecontactwiththeglobeholdercontacts. 

 ii)Positiontheglobelegsrmlyintothexedcontactsoftheglobeholder,applyingarmpressuretowardstherear.AVOID

 jerkingortwistingmovements.NOTE:GlobecanonlybemovedtotheleftandrightNOTupanddown.  

 iii)Mereplacementoftheglobeintotheglobeholderisoftennotsufcienttogiveaproperlyne-tunedbeam.Theoperator

 canovercomethisbyaligningthesplitlinealongthetopoftherotationlockingNIBandthesplitlineontheendofthe 

 handlewiththecentreoftheglobelament.(seeFig.1)        

iv) All other globes should be seated against the globe holder with little or no air gap.

v) Maximum globe wattage recommendation:

140 LANCE: 12V 75W

170 STRIKER: 12V 100W

240 BLITZ: 12V 100W

Note: USING GREATER WATTAGE WILL VOID WARRANTY

8. FOCUSING MECHANISM: The patented focus mechanism allows precise adjustment of the beam to various concentration

patternsasdesired.SimplyrotatethereectorandselectthedesiredSPOT.

9. DIMMER CONTROLLER FUNCTION:

Please see line drawing on next page

• The dimmer product is polarity sensitive (see line drawing)

• On/Off switch – This switch turns the light on and off. To turn light off, press and hold the on/off button for at least 0.5

seconds.

• Aquickpressoftheon/offswitchforlessthan0.5secondswhilethelightisonwillincreasethebrightnesstofull.

• Increasing Intensity Level – Press and hold this button will increase the intensity of the light.

• Decreasing Intensity Level – Press and hold this button will decrease the intensity of the light.

LIGHTFORCEAUSTRALIAPTYLTD•28OrsmondStreet,HindmarshSA5007Australia•www.lightforce.com|email:[email protected]

Australia:Tel:0884400888|Fax:0883460504•Int’l:Tel:+61884400888|Fax:+61883460504

LIGHTFORCEAUSTRALIAPty.Ltd.,shallbenotbeliablefordamage,malfunction,failureresultingfromaccident,misuse,misapplication,unauthorisedrepair,neglect,modication,unauthorisedornonstandardreplacementparts,accessories,

globes,batteriesorvoltageortheoperationoftheProductbeyonditstechnicalandenvironmentalspecications.

INSTRUCTION DATA

PRODUCT: SL Handheld Variable

VER: 1.1

DATE: JAN 2012

Fig.2

Fig.1

1 2

INSTRUCTION DATA 1

Podsumowanie treści

Strona 1 - INSTRUCTION DATA

1. DO NOT leave light connected to a power source when not in use. 2. DO NOT place light face down on ANY surface. If the light is switched on the in

Strona 2

• Memory Function – The light will store its last intensity level in memory when turned off. Operation of the variable power light at reduced brightn

Komentarze do niniejszej Instrukcji

Brak uwag

Lightforce HANDHELD SEARCHLIGHTS SL Variable Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Oświetlenie Lightforce HANDHELD SEARCHLIGHTS SL Variable. Lightforce HANDHELD SEARCHLIGHTS SL Variable User Manual [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Lightforce HANDHELD SEARCHLIGHTS SL Variable Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Oświetlenie Lightforce HANDHELD SEARCHLIGHTS SL Variable. Lightforce HANDHELD SEARCHLIGHTS SL Variable User Manual [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oświetlenie Lightforce HANDHELD SEARCHLIGHTS SL Variable